The DN370 has electronically-balanced input and output circuits to preserve the highest signal integrity. The inputs have excellent common-mode rejection and the outputs have high-drive capability to cope with long cable runs. Although equalisers are more generally used on console inserts, the DN370 is fully capable of being used in-line with cables running the long distances between the Front Of House mix position, the main stage and the delay towers in festival PA systems. Transformer balancing is available as an additional option on both the inputs and outputs. The notch filters on the DN370 can be used to eliminate a common problem with graphic equalisers - the control of frequencies that lie between the ISO standard frequency centres. The proportional-Q response of the DN370 simultaneously allows gentle contouring of the frequency spectrum and precise control of specific problem frequencies. Each equaliser shall use centre-detented slide potentiometers arranged to give a graphical display of frequency plotted against level. The slide potentiometers shall have protective covers to inhibit the ingress of dirt and dust. All audio connections shall be electronically balanced and use XLR and Phoenix style connectors.
Long-throw 45mm oil-damped faders with dust cover for increased accuracy and resolution.
All-new proportional-Q filters provide optimum control without undesirable audio artifacts.
Gain control with +6dB/-infinity range and centre detent at unity gain. Allows effective muting of channel in emergencies.
Range switch selects ±6dB or ±12dB operation for the faders, with LED indication.
Channel bypass switch with LED indication – the unit also provides automatic relay bypass in the event of power failure.
Sweepable high-pass filter with 20Hz to 500Hz range – sets the lower frequency limit of the system. The control incorporates a push switch to select the filter in and out, with an illuminated ring for “at a glance” status indication. Invaluable for smooth rejection of unwanted subsonic and low frequencies, particularly relevant with modern, compact wedge monitors.
Sweepable low-pass filter with 2kHz to 20kHz range – sets the upper frequency limit of the system. The control incorporates a push switch to select the filter in and out, with an illuminated ring for “at a glance” status indication. Provides optimum bandwidth control for vocal monitors and IEM systems.
Two sweepable notch filters per channel, with overlapping frequency ranges of 20Hz to 2kHz and 200Hz to 20kHz. These allow precise removal of problem frequencies with minimal effect on the rest of the program material, and fast control of “between fader” frequencies. This gives precise control of room and loudspeaker resonance/feedback nodes with minimum loss of energy – even between ISO centres. The controls each incorporate a push switch to select the filter in and out, with an illuminated ring for “at a glance” status indication.
Bypass switch with status LEDs for quick comparison of applied EQ.
Power switch, fully recessed in the “on” position to avoid accidental operation.
Signal present LEDs show the presence of audio signals above –40dBu.
Multi point clip monitoring. Clip warning LEDs illuminate when the level exceeds +20dBu (2dB below the onset of clipping) to assist in optimum system gain setting.
Electronically balanced inputs and outputs (transformer balancing is available as an option). Connections are provided on both XLRs (pin 2 hot) and Phoenix-type strip connectors for fixed installation.
IEC mains inlet. The unit automatically adjusts for operation on all voltages from 100 to 240V AC.
KT logo for quality engineering and reliability.
Rugged, roadworthy steel chassis.
Input type: Electronically balanced (pin 2 hot)
Input impedance: 20k ohms
Maximum input level: +22 dBu
Oputut type: electronically balanced (pin 2 hot)
Minimum output load impedance: 600 ohms
Output source impedance: < 60 ohms
Maximum output level: +22 dBu into > 2k ohms
Frequency response (+/-0.5 dBu): 20 Hz - 20 kHz
Distortion (THD+N): < 0.003% @ 1 kHz, +4 dBu
Dynamic range: > 114 dB (20Hz-20kHz unweighted, +/-12 dB range)
Overload indicator: +20 dBu
Gain: - infinity to + 6 dBu
Equalization: 30 bands
Maximum boost / cut: +/-12 dB, +/-6 dB
High pass filter slope: 12 dB / octave
Low pass filter slope: 12 dB / octave
Notch filter attenuation: > 17 dB, Q=32
Terminations: Audio 3-pin XLR and 6-pin Phoenix, Power 3-pin IEC
Voltage requirement: 100-240V AC
Power Consumption: < 60 W
Dimensions (H x W x D): 5.25" x 19" x 8" (133 x 482 x 205 mm)
Rack Spaces: 3 Units
Weight: 12.8 lbs. (5.8 kg)
Description$1,099.00 Add to cart
Description$549.99 Add to cart
12U Deluxe Shock Mount Amplifier Rack Case
Description$399.99 Add to cart
Classic Large-Diaphragm Cardioid Condenser Microphone
Description$69.95 Add to cart
Studio Microphone Cable Quad Conductor 25 feet
Description$59.99 Add to cart
5-in-1 Professional iPad Mini Stand with Included Mic Stand Pole Clamp, Table Clamp, and Gooseneck Extension
Description$49.95 Add to cart
Pro Dynamic Semi-Open Studio Headphones
Description$25.00 Add to cart
Gift Certificate (may be purchased in multiple amounts)